收藏本站
71M6543F/71M6543G Data Sheet
8
2.2.8
71M6xx3 Isolated Sensor Interface
2.2.8.1 General Description
Non-isolating sensors, such as shunt resistors, can be connected to the inputs of the 71M6543 via a
combination of a pulse transformer and a 71M6xx3 IC (a top-level block diagram of this sensor interface
is shown in Figure 31 ). The 71M6xx3 receives power directly from the 71M6543 via a pulse transformer
and does not require a dedicated power supply circuit. The 71M6xx3 establishes 2-way communication
with the 71M6543, supplying current samples and auxiliary information such as sensor temperature via a
serial data stream.
Up to three 71M6xx3 Isolated Sensors can be supported by the 71M6543. When a remote sensor
interface is enabled, the two analog current inputs become re-configured as a digital remote sensor
interface. For example, when control bit RMT2_E = 1, the IADC2-IADC3 analog pins are re-configured as
the digital interface pins to the remote sensor.
Each 71M6xx3 Isolated Sensor consists of the following building blocks:
?
?
?
?
?
?
Power supply that derives power from pulses received from the 71M6543
Bi-directional digital communications interface
Shunt signal pre-amplifier
22-bit 2nd Order Sigma-Delta ADC Converter with precision bandgap reference (chopping amplifier)
Temperature sensor (for digitally compensating VREF)
Fuse system containing part-specific information
During an ordinary multiplexer cycle, the 71M6543 internally determines which other channels are
enabled with MUX_DIV[3:0] (I/O RAM 0x2100[7:4]) . At the same time, it decimates the modulator output
from the 71M6xx3 Isolated Sensors. Each result is written to CE RAM during one of its CE access time
slots.
2.2.8.2 Communication between 71M6543 and 71M6xx3 Isolated Sensor
The ADC of the 71M6xx3 derives its timing from the power pulses generated by the 71M6543 and as a
result, operates its ADC slaved to the frequency of the power pulses. The generation of power pulses, as well
as the communication protocol between the 71M6543 and 71M6xx3 Isolated Sensor, is automatic and
transparent to the user. Details are not covered in this data sheet.
2.2.8.3 Control of the 71M6xx3 Isolated Sensor
The 71M6543 can read or write certain types of information from each 71M6xx3 remote sensor.
The data to be read is selected by a combination of the RCMD[4:0] and TMUXRn[2:0] . To perform a read
transaction from one of the 71M6xx3 devices, the MPU first writes the TMUXRn[2:0] field (where n = 2, 4, 6,
located at I/O RAM 0x270A[2:0] , 0x270A[6:4] and 0x2709[2:0] , respectively). Next, the MPU writes
RCMD[4:0] ( SFR 0xFC[4:0] ) with the desired command and phase selection. When the RCMD[4:2] bits
have cleared to zero, the transaction has been completed and the requested data is available in
RMT_RD[15:0] ( I/O RAM 0x2602[7:0] is the MSB and 0x2603[7:0] is the LSB). The read parity error bit,
PERR_RD (SFR 0xFC[6]) is also updated during the transaction. If the MPU writes to RCMD[4:0] before a
previously initiated read transaction is completed, the command is ignored. Therefore, the MPU must wait
for RCMD[4:2] =0 before proceeding to issue the next remote sensor read command.
If the CE is running ( CE_E =1), the MPU must write RCMD[4:0] immediately after a CE_BUSY rising
edge. RCMD[4:0] must be written before the next rising edge of MUX_SYNC. Failure to do this can cause
incorrect data to be read.
The RCMD[4:0] field is divided into two sub-fields, COMMAND=RCMD[4:2] and PHASE=RCMD[1:0] , as
shown in Table 4 .
.
22
v2
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
71M6545-IGT/F IC ENERGY METERING
720-10007-00300 CBL D-SUB 9PIN FMAL-25PIN FML 3M
720-10010-00025 CBL DSUB 9PIN FML-25PIN MAL .25M
720-10020-00300 CBL DSUB 9PIN FML-9PIN MALE 3M
720-10021-00300 CBL DSUB 9PIN FML-9PIN FEMAL 3M
72231-0881 8 POS T/P SHLD 4 GR ASSY
7250B PANEL KIT BOTTOM FOR R-1220 CASE
731-10061-00200 CBL DSUB HD 15FEMAL-15MALE 2.0M
相关代理商/技术参数
71M6543F-IGTR/F 功能描述:计量片上系统 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel
71M6543FT-IGT/F 制造商:Maxim Integrated Products 功能描述:ENERGY METER ICS - Rail/Tube
71M6543FT-IGTR/F 制造商:Maxim Integrated Products 功能描述:3-PHASE SOC, 64KB FLASH, PRES TEMP SENSOR - Tape and Reel
71M6543G 制造商:MAXIM 制造商全称:Maxim Integrated Products 功能描述:Selectable Gain of 1 or 8 for One Current Energy Meter ICs Metrology Compensation
71M6543GH 制造商:未知厂家 制造商全称:未知厂家 功能描述:电表IC
71M6543GHT-IGT/F 制造商:Maxim Integrated Products 功能描述:3-PHASE, 128KB, PRES TEMP SENSOR, HI PREC - Bulk
71M6543GHT-IGTR/F 制造商:Maxim Integrated Products 功能描述:3-PHASE, 128KB, PRES TEMP SENSOR, HI PREC - Tape and Reel
71M6543G-IGT/F 功能描述:计量片上系统 - SoC Precision Energy Meter IC RoHS:否 制造商:Maxim Integrated 核心:80515 MPU 处理器系列:71M6511 类型:Metering SoC 最大时钟频率:70 Hz 程序存储器大小:64 KB 数据 RAM 大小:7 KB 接口类型:UART 可编程输入/输出端数量:12 片上 ADC: 安装风格:SMD/SMT 封装 / 箱体:LQFP-64 封装:Reel